Description
Kenwood KAC-M3004 Compact 4 Channel Digital Amplifier
Kenwood's KAC-M3004 compact 4-channel amplifier will power up the music in your vehicle with 50 watts RMS per channel. That's enough to hear everything clearly above the noise of the road, trail, or waterway as you travel along. This little powerhouse will fit almost anywhere, including a storage compartment on a boat, motorcycle, or ATV, so you can install great sound in whatever vehicle you wish. Installing a pair of subs? You can bridge this amp to 2-channel mode and send 150 watts to each subwoofer.
Product Highlights:
- 4-channel car amplifier
- 50 watts RMS x 4 at 4 ohms (75 watts RMS x 4 at 2 ohms)
- 150 watts x 2 bridged at 4 ohms
- CEA-2006 compliant
- Class D amp technology
- Conformal-coated circuit board — suitable for power sports and marine applications
- Variable high- and low-pass filters (50-200 Hz, 12 dB/octave)
- Preamp and speaker-level inputs
- Fuse rating: 30A x 1
- 10-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- Dimensions: 7-5/8"W x 1-13/16"H x 3-7/8"D
- Warranty: 1 year
- Our 30-day money-back guarantee
- MFR # KAC-M3004
What's in the box
- 4-Channel Amplifier With A 30a Atm Mini-Fuse Installed
- 9" Speaker Output Harness (8-Pin Molex Plug On One End)
- 4 Self-Tapping Screws (M4 X 16mm)
- Two 13.5" Plastic Wire Ties
- Clear Plastic Self-Adhesive Protective Covers For Controls (2 Sheets)
- Instruction Manual/Warranty Card
Weather-resistant protection for music on the go
Conformal coating protects the internal circuits from water and dirt, so the show will always go on, even through the roughest conditions. The speaker output terminals feature plastic-covered plugs that provide further protection for those connections.
High-level inputs ease installation
The KAC-M3004 will accept a signal from just about any source, whether you're using RCA cables from an aftermarket receiver or speaker wires from a factory radio. When you use the speaker-level inputs, the amplifier will sense the signal and turn itself on, so you won't need to run a remote turn-on lead to your car stereo.
Kenwood KAC-M3004 - Power your music wherever you go
Kenwood's KAC-M3004 compact 4-channel amplifier will power up the music in your vehicle with 50 watts RMS per channel. That's enough to hear everything clearly above the noise of the road, trail, or waterway as you travel along. This little powerhouse will fit almost anywhere, including a storage compartment on a boat, motorcycle, or ATV, so you can install great sound in whatever vehicle you wish. Installing a pair of subs? You can bridge this amp to 2-channel mode and send 150 watts to each subwoofer.
High-level inputs easy installation
The KAC-M3004 will accept a signal from just about any source, whether you're using RCA cables from an aftermarket receiver or speaker wires from a factory radio. When you use the speaker-level inputs, the amplifier will sense the signal and turn itself on, so you won't need to run a remote turn-on lead to your car stereo.
Compact Amplifier
The Kenwood KAC-M3004 compact Class D 4-channel amplifier is designed to boost the output and clarity of your car stereo. The amp features a conformal coating on the circuit board to protect it from moisture. This allows you to use the amp for motorcycles, marine applications, or on All-Terrain Vehicles (ATVs). The KAC-M3004 delivers 50 watts RMS x 4 channels at 4 ohms. It also gives you 75 watts RMS x 4 at 2 ohms, or 150 watts RMS x 2 channels at 4 ohms bridged.
Connections
Power/Power Control Connections: The power, ground, and power control connections are 0.35" wide screw terminals. A Phillips-head or flat blade screw driver (not supplied) is required to tighten/loosen the terminals. Spade connectors or ring terminals are recommended. A minimum 10-gauge wire is required for power and ground.
Power Control: The Power Control wire should be connected to the head unit's remote turn-on lead when an aftermarket unit is used. This wire does not need to be connected if you're using speaker level inputs. The Signal-sensing Turn-on feature will turn on the amplifier when an input signal is detected.
Line-Level Inputs: The amplifier is equipped with two pairs of RCA inputs for connecting stereo RCA patch cables from the head unit to the amp. If using a factory head unit, or a unit without preamp outputs, you can splice the speaker wires to an RCA plug, maintaining the same polarity.
Additional Information
Shipping & Return
Reviews
My Wishlist
Wishlist is empty.
Compare
Shopping cart
